Request Quotation

The design and fabrication of each Wilson Heat Exchanger™ meets the exact requirements and specifications for its application. To receive a cost quotation for your specific needs, please complete and submit this form. Supply at least all required information (*), and call Wilson TurboPower if you need assistance.

Provide cost quotation and product specifications
Send to
*Name
*Company
*Address
*City
*State/Province/Country
Contact by
Phone
Fax
*Email
Project reference
*Application description
Current heat exchanger to be replaced (if applicable)
Type (gas-to-gas)	--select one-- Shell and tube Plate and frame Regenerator Recuperator Other -->
Volume	<0.15 0.3 0.6 1.0 3.0 6.0 10 15 25 35 50 >50 -- Cubic meters (m3)  or <5 10 20 35 100 200 350 500 900 1700 >1700 -- Cubic feet (ft3)
Dimensions	Heat exchanger core Overall dimensions including ducts Overall dimensions excluding ducts --select one--
	W x L x H   -- inches cm units
Effectiveness	>90% 85% 80% 70% 60% 50% 40% <40% -- thermal efficiency %
Average service intervals	<200 hrs 500 hrs 1,000 hrs 1,500 hrs 2,000 hrs 2,500 hrs 3,000 hrs 4,000 hrs 5,000 hrs 6,000 hrs 8,000 hrs 10,000 hrs >10,000 hrs -- MTBS operating hours
System life	<5,000 hrs 10,000 hrs 20,000 hrs 30,000 hrs 40,000 hrs 50,000 hrs 60,000 hrs 70,000 hrs 80,000 hrs 90,000 hrs 100,000 hrs >100,000 hrs -- operating hours
Replacement cost	-- <$1,000 $5,000 $10,000 $15,000 $20,000 $40,000 $60,000 $80,000 $100,000 $150,000 $200,000 $250,000 $300,000 $400,000 $500,000 $750,000 $1,000,000 $1,500,000 $2,000,000 >$2,000,000 USD
Additional information or comments about the current heat exchanger to be replaced
Wilson Heat Exchanger application specifications
*Primary requirements	Very important Important Not important
High effectiveness
Small size/footprint
Low pressure drop
High-temperature capability
Material compatibility
Variable effectiveness
Additional information or comments about important requirements
Effectiveness required/desired or specify HOT outlet temperature where requested	-- 97% 95% 92.5% 90% 87.5% 85% 82.5% 80% 77.5% 75% 72.5% 70% 67.5% 65% 62.5% 60% 57.5% 55% 52.5% 50% thermal efficiency %
*Outlet temperature fluctuation limit	-- <1 <5 <10 <20 <30 <40 <50 <75 <100 <150 no limit °C  or  -- <2 <10 <20 <40 <60 <80 <100 <150 <200 <300 no limit °F
*Allowable contamination from high-pressure flow to low-pressure flow	--select one-- Acceptable Not acceptable
*Gas type for HOT flow	--select one-- Air Exhaust from natural gas combustion process Exhaust from biomass combustion process Exhaust from other combustion process Steam Other (specify below)
*Flow rate for HOT flow	Nm^3/hr Nm^3/s kg/hr kg/s lb/hr lb/s SCFH SCFM -- units
*Inlet temperature for HOT flow	°C °F °K -- units
*Inlet pressure for HOT flow	H2O psia psig kPa -- units
Outlet temperature for HOT flow (*required only if effectiveness % is not provided)	°C °F °K -- units
*Gas type for COLD flow	--select one-- Air Other (specify below)
*Flow rate for COLD flow	Nm^3/hr Nm^3/s kg/hr kg/s lb/hr lb/s SCFH SCFM -- units
*Inlet temperature for COLD flow	°C °F °K -- units
*Inlet pressure for COLD flow	H2O psia psig kPa -- units
*Absolute pressure loss from inlet HOT flow	-- 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 35 40 45 no limit Inches H20  or  -- 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 7.0 8.0 9.0 10.0 no limit Kilopascal (kPa)
*Absolute pressure loss from inlet COLD flow	-- 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 35 40 45 no limit Inches H20  or  -- 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 5.0 5.5 6.0 7.0 8.0 9.0 10.0 no limit Kilopascal (kPa)
*Maximum allowable pressure drop in the HOT flow	-- 0.5% 1.0% 1.5% 2.0% 2.5% 3.0% 3.5% 4.0% 4.5% 5.0% 5.5% 6.0% 7.0% 8.0% 9.0% 10.0% no limit Relative pressure loss (p/pin=%)
*Maximum allowable pressure drop in the COLD flow	-- 0.5% 1.0% 1.5% 2.0% 2.5% 3.0% 3.5% 4.0% 4.5% 5.0% 5.5% 6.0% 7.0% 8.0% 9.0% 10.0% no limit Relative pressure loss (p/pin=%)
Additional information or comments about effectiveness, temperature, or pressure
Quantity needed
First order
Delivery by
Future orders
Delivery by
Additional information or comments about quantity needed
Additional data
Please mark box if you are separately sending documentation that may include process flow diagrams, equipment drawings, or other information.        Send to quotedocs@wilsonturbopower.com